3D Model Datasheet

MS412PJD Series

Common Mode Chokes for Critical Applications

Only 1.4 mm high and 3 mm square
Ideal for use in both power line and signal line applications
Common- and differential-mode filtering in a single device
Up to 540 MHz differential mode cutoff frequency
Can be used as coupled inductors for SEPIC applications
The tin-lead (Sn-Pb) termination offers the best possible board adhesion.

Request Quote:

Part number

Find my part

;

Specifications

Part number 1	Common mode peak impedance (kΩ)	Cutoff frequency (MHz) 2	Inductance (µH) 3	Irms (A) 4	DCR max (Ω) 5	Isolation Voltage (Vrms) 6
Part number 1	Common mode peak impedance (kΩ)	Cutoff frequency (MHz) 2	Inductance (µH) 3	Irms (A) 4	DCR max (Ω) 5	Isolation Voltage (Vrms) 6
MS412PJD391NSZ	1.03 @ 330 MHz	540	0.39 ±30%	1.45	0.071	100
MS412PJD561MSZ	1.44 @ 240 MHz	540	0.56 ±20%	1.37	0.079	100
MS412PJD102MSZ	2.43 @ 160 MHz	330	1.0 ±20%	1.08	0.129	100
MS412PJD152MSZ	3.56 @ 130 MHz	330	1.5 ±20%	0.86	0.204	100
MS412PJD182MSZ	4.37 @ 110 MHz	280	1.8 ±20%	0.78	0.273	100
MS412PJD222MSZ	4.67 @ 100 MHz	330	2.2 ±20%	0.75	0.3	100
MS412PJD332MSZ	7.28 @ 81 MHz	220	3.3 ±20%	0.67	0.337	100
MS412PJD472MSZ	10.7 @ 66 MHz	210	4.7 ±20%	0.54	0.503	100
MS412PJD682MSZ	12.1 @ 54 MHz	290	6.8 ±20%	0.49	0.622	100
MS412PJD103MSZ	17.8 @ 47 MHz	330	10 ±20%	0.38	1.04	100
MS412PJD153MSZ	22.6 @ 33 MHz	140	15 ±20%	0.32	1.42	100
MS412PJD183MSZ	29.0 @ 31 MHz	94.0	18 ±20%	0.31	1.55	100
MS412PJD223MSZ	27.3 @ 24 MHz	88.0	22 ±20%	0.28	1.89	100
MS412PJD333MSZ	41.1 @ 21 MHz	59.0	33 ±20%	0.23	2.84	100
MS412PJD473MSZ	48.7 @ 18 MHz	50.0	47 ±20%	0.19	4.03	100
MS412PJD683MSZ	64.5 @ 14 MHz	48.0	68 ±20%	0.16	6.11	100
MS412PJD104MSZ	94.7 @ 13 MHz	47.0	100 ±20%	0.13	8.54	100
MS412PJD124MSZ	116 @ 11 MHz	37.0	120 ±20%	0.13	9.23	100
MS412PJD154MSZ	135 @ 9 MHz	27.0	150 ±20%	0.11	12.4	100
MS412PJD184MSZ	170 @ 8 MHz	39.0	180 ±20%	0.10	15.32	100
MS412PJD224MSZ	155 @ 7 MHz	27.0	220 ±20%	0.09	18.56	100
MS412PJD334MSZ	222 @ 6 MHz	16.0	330 ±20%	0.07	27.7	100

Notes

When ordering, please specify screening code: e.g.MS412PJD334MSZ.
Frequency at which the differential mode attenuation equals −3 dB.
Inductance shown for each winding, measured at 100 kHz, 0.1 Vrms, 0 Adc on an Agilent/HP 4284A LCR meter or equivalent.
Current that causes a 40°C temperature rise from 25°C ambient. This information is for reference only and does not represent absolute maximum ratings.
DCR is for each winding.
Interwinding isolation (hipot) tested for one minute.

Termination:

S = Tin-lead (63/37) over tin over nickel.

Testing:

Z = Unscreened
Y = Unscreened (SLDC Option A)
W = Unscreened (SLDC Option B)
H = Coilcraft CP-SA-10001 Group A
G = Coilcraft CP-SA-10001 Group A (SLDC Option A)
D = Coilcraft CP-SA-10001 Group A (SLDC Option B)
N = Group A screening per Coilcraft CP-SA-10004
- Screening performed to the document’s latest revision.
- Custom testing also available.

Environmental

Ambient temperature range:

–55°C to +105°C with Irms current.

Storage temperature range:

Component: –55°C to +155°C.
Tape and reel packaging: –55°C to +80°C.

Maximum part temperature:

+155°C (ambient + temp rise).

Failures in Time (FIT) / Mean Time Between Failures (MTBF):

See FIT/MTBF Calculations

Performance curves

Attenuation (Ref: 50 Ohms)

Impedance vs Frequency

Physical characteristics

General specification

Core Material:

Ferrite

Weight:

48 – 66 mg

Winding to Winding Isolation:

100

Soldering/Washing

Moisture Sensitivity Level (MSL):

1 (unlimited floor life at <30°C / 85% relative humidity).

Resistance to soldering heat:

Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles.

Refer to Soldering Coilcraft Components before soldering.

PCB Washing:

Tested to MIL-STD-202 Method 215 plus an additional aqueous wash. See Doc787_PCB_Washing.pdf.